True Temper Dynamic Gold MID 100 Iron Shafts
True Temper Dynamic Gold MID 100 Iron Shafts
A More Playable Dynamic Gold Trajectory
True Temper Dynamic Gold MID 100 combines a lighter steel construction with a mid-launch profile for golfers seeking increased trajectory and enhanced playability. It preserves the stable feedback and consistency associated with Dynamic Gold while making it easier to produce a playable ball flight.
At approximately 105–106 grams, Dynamic Gold MID 100 sits well below the weight of traditional Dynamic Gold models. This reduction can help golfers generate speed more efficiently while retaining the solid feel and dependable control of a steel iron shaft.
Mid-Launch Flight
Engineered to help golfers produce a higher, more playable trajectory than traditional low-launch Dynamic Gold profiles.
Lighter Steel Design
The 105–106 gram construction can make the club easier to swing without requiring a move to graphite.
Enhanced Playability
A balanced combination of manageable weight, usable trajectory and consistent steel-shaft feedback.
Stable Performance
Low-torque construction helps support predictable delivery and consistent performance throughout the set.
Performance Profile
| Shaft Material | Steel |
| Trajectory | Mid launch |
| Weight Range | 105–106 grams |
| Torque | Low |
| Available Flexes | R300 and S300 |
Dynamic Gold MID 100 Specifications
| Flex | Weight | Tip Options | Butt Diameter | Torque |
|---|---|---|---|---|
| R300 | 105g | .355″ taper / .370″ parallel | .600″ | Low |
| S300 | 106g | .355″ taper / .370″ parallel | .600″ | Low |
Choose the Correct Tip Configuration
.355″ Taper Tip
The .355″ taper-tip version uses a club-specific raw shaft length for each iron. Select the shaft length corresponding to the club being assembled.
Taper-tip shafts should not be tip trimmed. Install the correct discrete shaft and butt trim it to the finished playing length.
.370″ Parallel Tip
The .370″ parallel-tip version is supplied as a 40.5″ master-length shaft in both R300 and S300 flexes.
Parallel-tip shafts require club-specific tip trimming followed by butt trimming to the finished playing length.
.355″ Taper-Tip Length Guide
Select the raw shaft length corresponding to the iron being assembled.
| Club | 3 | 4 | 5 | 6 | 7 | 8 | 9/W |
|---|---|---|---|---|---|---|---|
| Raw Length | 40″ | 39.5″ | 39″ | 38.5″ | 38″ | 37.5″ | 37″ |
.370″ Parallel-Tip Trimming Guide
True Temper provides the following general trimming progression for parallel-tip iron shafts.
| Club | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | Wedge |
|---|---|---|---|---|---|---|---|---|---|
| Tip Trim | 0″ | 0″ | 0.5″ | 1″ | 1.5″ | 2″ | 2.5″ | 3″ | 3.5″ |
Butt trim to the finished playing length after completing the required tip trimming. These are general manufacturer recommendations; an experienced club builder may adjust the build to fit the golfer and clubhead.
Who Is It For?
- Golfers seeking a mid-launch iron trajectory
- Players who want lighter-weight steel performance
- Golfers who need more playability than a traditional low-launch profile
- Players who prefer the feedback and consistency of steel
- Golfers building or reshafting a properly fitted iron set
Flex Selection
R300: Regular flex weighing approximately 105 grams for golfers with moderate speed, a smoother transition or a preference for a more responsive feel.
S300: Stiff flex weighing approximately 106 grams for golfers with greater speed, a firmer transition or a preference for additional stability.
What Is Included?
This listing is for one uncut True Temper Dynamic Gold MID 100 steel iron shaft in the selected flex, tip diameter and raw length.
Clubhead, grip, ferrule and installation services are not included unless specifically selected or stated elsewhere on the product page.
Professional Installation Recommended
Correct shaft preparation, trimming, ferrule installation, epoxy bonding, final-length measurement and swing-weight management are essential to achieving the intended performance.
Do not tip trim the .355″ taper-tip version. The .370″ parallel-tip version must be tip trimmed for the intended club and then butt trimmed to the final playing length.
View True Temper Trim InstructionsNeed Help Selecting the Correct Shaft?
Flex, tip diameter, raw length and final build specifications all influence performance. Grater Golf can help you select the correct Dynamic Gold MID 100 configuration for your irons.
Talk to Grater GolfProduct specifications and availability are based on current manufacturer information and may change without notice. Shaft performance can vary according to the golfer, clubhead, build specifications and installation. Product images are for reference. Confirm flex, hosel diameter and raw length before ordering.
Shipping & Returns
Free standard shipping on most orders $100+ within the contiguous U.S. Eligible items may be returned within 30 days. Custom, modified, cut, installed, and made-to-order products may be final sale.